HDPWS

Data Access

PARKER SOLAR PROBE FIELDS Level 2 DFB Search Coil Magnetometer (SCM) Burst Waveform (DBM) Data (CDF)

ResourceID
spase://CNES/NumericalData/CDPP-Archive/PSP/FIELDS/SCM/PARKERSP_FIELDS_SCM_DBM

Description
This data set contains the PARKER SOLAR PROBE FIELDS Level 2 Search-coil (SCM) burst waveform data from the low-frequency (LF) antennas. In contrast to regular waveforms, bursts are recorded at higher frequency and for short time intervals. The waveforms consist of 3 components of the magnetic field, expressed in sensor coordinates (Bu, Bv, Bw) and in spacecraft coordinates (Bx, By, Bz). For the description of the coordinate systems, see the description of the SCM. Time (epoch) is in TT2000 format and corresponds to nanoseconds since 1 Jan 2000 12:00:00 with leap seconds included. Burst waveforms are general recorded below 0.25 AU but not exclusively at perihelion. They are triggered by events seen in the electric field. Their time resolution is 150000 Hz / 2^N with, in general, N=1. The LF antennas of the SCM have an upper frequency rolloff at 10 kHz. For that reason, waveforms are more likely to be contaminated by noise above 10 kHz. Burst waveforms of the Search-Coil Magnetometer (SCM) [Jannet et al., 2021] are registered by the Digital Fields Board (DFB) instrument [Malaspina et al., 2016], which is part of the FIELDS suite [Bale et al., 2016]. DFB provides waveform data for various FIELDS sensors. The Level 2 data products are calibrated for : 1. DFB in-band gain, 2. DFB analog filter gain/phase response, 3. DFB digital filter phase (*not* gain) response, and 4. the search coil preamplifier gain/phase response (when applicable). Calibrations for the DFB digital filter gain response have *not* been implemented, but the required convolution kernel is provided in the cdf datafiles. The reason for not including this gain response to the L2 data is because this can introduce unphysical enhancements of spectral power at high frequencies when the uncorrected signal is dominated by noise. This effect should be examined carefully when determining spectral slopes and features at the highest frequencies. All magnetic fields are expressed in nT. Calculation of the PSP-Sun distance for the selection criterion (see Filter tab) is realized each day at 00:00. SCM anomaly: From 3 March 2019 onwards the LF Bu antenna lost its sensitivity below 1 kHz. This problem occurs whenever the sensor is cold, i.e. at perihelion. At the same time, the sensitivity of the LF Bu antenna to periodic spikes associated with heater cycling has increased by two orders of magnitude. The data are correct for encounter 1 (October-November 2018) only. For subsequent encounters, only Bv and Bw should be used, or Bu above 1 kHz. References: FIELDS website: https://fields.ssl.berkeley.edu/ [2] Bale, S. et al. (2016), The FIELDS Instrument Suite for Solar Probe Plus. Measuring the Coronal Plasma and Magnetic Field, Plasma Waves and Turbulence, and Radio Signatures of Solar Transients, Space Science Reviews, Volume 204, Issue 1-4, pp.49-82, doi:10.1007/s11214-016-0244-5 [3] Malaspina, D.M., Ergun, R.E., Bolton, M. et al. (2016), The Digital Fields Board for the FIELDS instrument suite on the Solar Probe Plus mission: Analog and digital signal processing, Journal of Geophysical Research: Space Physics, 121, 5088-5096, doi: 10.1002/2016JA022344 [4] Jannet, G., Dudok de Wit, T., Krasnoselskikh, V. et al. (2021), Measurement of magnetic field fluctuations in the parker solar probe and solar orbiter missions, Journal of Geophysical Research: Space Physics, 126, e2020JA028543 doi: 10.1029/2020JA028543

View XML | Edit

Details

Version:2.4.0

NumericalData

ResourceID
spase://CNES/NumericalData/CDPP-Archive/PSP/FIELDS/SCM/PARKERSP_FIELDS_SCM_DBM
ResourceHeader
ResourceName
PARKER SOLAR PROBE FIELDS Level 2 DFB Search Coil Magnetometer (SCM) Burst Waveform (DBM) Data (CDF)
DOI
https://doi.org/10.24400/802406/geps-5yaw
ReleaseDate
2022-07-04 15:46:59Z
Description
This data set contains the PARKER SOLAR PROBE FIELDS Level 2 Search-coil (SCM) burst waveform data from the low-frequency (LF) antennas. In contrast to regular waveforms, bursts are recorded at higher frequency and for short time intervals. The waveforms consist of 3 components of the magnetic field, expressed in sensor coordinates (Bu, Bv, Bw) and in spacecraft coordinates (Bx, By, Bz). For the description of the coordinate systems, see the description of the SCM. Time (epoch) is in TT2000 format and corresponds to nanoseconds since 1 Jan 2000 12:00:00 with leap seconds included. Burst waveforms are general recorded below 0.25 AU but not exclusively at perihelion. They are triggered by events seen in the electric field. Their time resolution is 150000 Hz / 2^N with, in general, N=1. The LF antennas of the SCM have an upper frequency rolloff at 10 kHz. For that reason, waveforms are more likely to be contaminated by noise above 10 kHz. Burst waveforms of the Search-Coil Magnetometer (SCM) [Jannet et al., 2021] are registered by the Digital Fields Board (DFB) instrument [Malaspina et al., 2016], which is part of the FIELDS suite [Bale et al., 2016]. DFB provides waveform data for various FIELDS sensors. The Level 2 data products are calibrated for : 1. DFB in-band gain, 2. DFB analog filter gain/phase response, 3. DFB digital filter phase (*not* gain) response, and 4. the search coil preamplifier gain/phase response (when applicable). Calibrations for the DFB digital filter gain response have *not* been implemented, but the required convolution kernel is provided in the cdf datafiles. The reason for not including this gain response to the L2 data is because this can introduce unphysical enhancements of spectral power at high frequencies when the uncorrected signal is dominated by noise. This effect should be examined carefully when determining spectral slopes and features at the highest frequencies. All magnetic fields are expressed in nT. Calculation of the PSP-Sun distance for the selection criterion (see Filter tab) is realized each day at 00:00. SCM anomaly: From 3 March 2019 onwards the LF Bu antenna lost its sensitivity below 1 kHz. This problem occurs whenever the sensor is cold, i.e. at perihelion. At the same time, the sensitivity of the LF Bu antenna to periodic spikes associated with heater cycling has increased by two orders of magnitude. The data are correct for encounter 1 (October-November 2018) only. For subsequent encounters, only Bv and Bw should be used, or Bu above 1 kHz. References: FIELDS website: https://fields.ssl.berkeley.edu/ [2] Bale, S. et al. (2016), The FIELDS Instrument Suite for Solar Probe Plus. Measuring the Coronal Plasma and Magnetic Field, Plasma Waves and Turbulence, and Radio Signatures of Solar Transients, Space Science Reviews, Volume 204, Issue 1-4, pp.49-82, doi:10.1007/s11214-016-0244-5 [3] Malaspina, D.M., Ergun, R.E., Bolton, M. et al. (2016), The Digital Fields Board for the FIELDS instrument suite on the Solar Probe Plus mission: Analog and digital signal processing, Journal of Geophysical Research: Space Physics, 121, 5088-5096, doi: 10.1002/2016JA022344 [4] Jannet, G., Dudok de Wit, T., Krasnoselskikh, V. et al. (2021), Measurement of magnetic field fluctuations in the parker solar probe and solar orbiter missions, Journal of Geophysical Research: Space Physics, 126, e2020JA028543 doi: 10.1029/2020JA028543
Acknowledgement
Please add the following to your acknowledgements when using SCM data: The authors acknowledge CNES (Centre National d'Etudes Spatiales), NASA and CNRS (Centre National de la Recherche Scientifique) for their support to the PSP/SCM team, and the CDPP (Centre de Données de la Physique des Plasmas) for the distribution of the PSP/SCM data. The FIELDS experiment on the PSP spacecraft was designed and developed under NASA contract NNN06AA01C. Other datasets from FIELDS can be found at https://fields.ssl.berkeley.edu/ . For other instruments of Parker Solar Probe, see https://cdaweb.gsfc.nasa.gov/index.html/ Please cite the following reference papers when using SCM data: G. Jannet, T. Dudok de Wit, V. Krasnoselskikh, M. Kretzschmar, P. Fergeau, M. Bergerard-Timofeeva, C. Agrapart, J.-Y. Brochot, G. Chalumeau, P. Martin, C. Revillet, S. D. Bale, M. Maksimovic, T. A. Bowen, C. Brysbaert, K. Goetz, E. Guilhem, P. R. Harvey, V. Leray, and E. Lorfèvre, Measurement of magnetic field fluctuations in the Parker Solar Probe and solar orbiter missions, Journal of Geophysical Research: Space Physics, 126 (2021), e2020JA028543, doi:10.1029/2020JA028543 [NASA ADS: https://ui.adsabs.harvard.edu/abs/2021JGRA..12628543J]
Contacts

AccessInformation
RepositoryID
Availability
Online
AccessURL
Name
REGARDS
URL
Description
Access via CNES Data Archive for CDPP
Format
CDF
ProcessingLevel
Calibrated
ProviderProcessingLevel
2
InstrumentIDs
MeasurementType
MagneticField
TemporalDescription
TimeSpan
StartDate
2018-08-13 00:00:00Z
StopDate
2021-11-26 00:00:00Z
ObservedRegion
Heliosphere
ObservedRegion
Heliosphere.Inner
ObservedRegion
Heliosphere.NearEarth
ObservedRegion
Sun.Corona
Parameter #1
Name
Burst Waveform from Bu axis
Description
L2 AC Burst Search Coil from Bu axis
Units
nT
UnitsConversion
1e-9>T
Field
Qualifier
Array
Qualifier
Component.I
FieldQuantity
Magnetic
Parameter #2
Name
Burst Search Coil from Bu axis rms value
Description
L2 AC Burst Search Coil from Bu axis rms value
Units
nT
UnitsConversion
1e-9>T
Field
Qualifier
Scalar
Qualifier
Component.I
FieldQuantity
Magnetic
Parameter #3
Name
AC Burst Search Coil from Bu axis max value
Description
L2 AC Burst Search Coil from Bu axis max value
Units
nT
UnitsConversion
1e-9>T
Field
Qualifier
Scalar
Qualifier
Component.I
FieldQuantity
Magnetic
Parameter #4
Name
AC Burst Search Coil from Bu axis min value
Description
L2 AC Burst Search Coil from Bu axis min value
Units
nT
UnitsConversion
1e-9>T
Field
Qualifier
Scalar
Qualifier
Component.I
FieldQuantity
Magnetic
Parameter #5
Name
AC Burst Search Coil from Bu axis median value
Description
L2 AC Burst Search Coil from Bu axis median value
Units
nT
UnitsConversion
1e-9>T
Field
Qualifier
Scalar
Qualifier
Median
Qualifier
Component.I
FieldQuantity
Magnetic
Parameter #6
Name
Burst Waveform from Bv axis
Description
L2 AC Burst Search Coil from Bv axis
Units
nT
UnitsConversion
1e-9>T
Field
Qualifier
Array
Qualifier
Component.J
FieldQuantity
Magnetic
Parameter #7
Name
Burst Search Coil from Bv axis rms value
Description
L2 AC Burst Search Coil from Bv axis rms value
Units
nT
UnitsConversion
1e-9>T
Field
Qualifier
Scalar
Qualifier
Component.J
FieldQuantity
Magnetic
Parameter #8
Name
Burst Search Coil from Bv axis max value
Description
L2 AC Burst Search Coil from Bv axis max value
Units
nT
UnitsConversion
1e-9>T
Field
Qualifier
Maximum
Qualifier
Scalar
Qualifier
Component.J
FieldQuantity
Magnetic
Parameter #9
Name
Burst Search Coil from Bv axis min value
Description
L2 AC Burst Search Coil from Bv axis min value
Units
nT
UnitsConversion
1e-9>T
Field
Qualifier
Minimum
Qualifier
Scalar
Qualifier
Component.J
FieldQuantity
Magnetic
Parameter #10
Name
Burst Search Coil from Bv axis median value
Description
L2 AC Burst Search Coil from Bv axis median value
Units
nT
UnitsConversion
1e-9>T
Field
Qualifier
Scalar
Qualifier
Component.J
FieldQuantity
Magnetic
Parameter #11
Name
Burst Waveform from Bw axis
Description
L2 AC Burst Search Coil from Bw axis
Units
nT
UnitsConversion
1e-9>T
Field
Qualifier
Array
Qualifier
Component.K
FieldQuantity
Magnetic
Parameter #12
Name
Burst Search Coil from Bw axis rms value
Description
L2 AC Burst Search Coil from Bw axis rms value
Units
nT
UnitsConversion
1e-9>T
Field
Qualifier
Scalar
Qualifier
Component.K
FieldQuantity
Magnetic
Parameter #13
Name
Burst Search Coil from Bw axis max value
Description
L2 AC Burst Search Coil from Bw axis max value
Units
nT
UnitsConversion
1e-9>T
Field
Qualifier
Scalar
Qualifier
Component.K
FieldQuantity
Magnetic
Parameter #14
Name
Burst Search Coil from Bw axis min value
Description
L2 AC Burst Search Coil from Bw axis min value
Units
nT
UnitsConversion
1e-9>T
Field
Qualifier
Scalar
Qualifier
Component.K
FieldQuantity
Magnetic
Parameter #15
Name
Burst Search Coil from Bw axis median value
Description
L2 AC Burst Search Coil from Bw axis median value
Units
nT
UnitsConversion
1e-9>T
Field
Qualifier
Scalar
Qualifier
Component.K
FieldQuantity
Magnetic
Parameter #16
Name
FIELDS quality flag
Description
FIELDS quality flags. This is a bitwise variable, meaning that multiple flags can be set for a single time, by adding flag values. Current flagged values are: 1: FIELDS antenna bias sweep, 2: PSP thruster firing, 4: SCM Calibration, 8: PSP rotations for MAG calibration (MAG rolls), 16: FIELDS MAG calibration sequence, 32: SWEAP SPC in electron mode, 64: PSP Solar limb sensor (SLS) test. 128: PSP spacecraft is off umbra pointing. A value of zero corresponds to no set flags. Not all flags are relevant to all FIELDS data products, refer to notes in the CDF metadata and on the FIELDS SOC website for information on how the various flags impact FIELDS data. Additional flagged items may be added in the future.
Support
SupportQuantity
DataQuality